<*********>锤破制砂机供应厂家锤破制砂机锤破<*********>破碎<*********>机 

锤式破碎机的保养方法有哪些

1、定期检查机器内部部件的磨损情况要定期检查机器内部部件的磨损情况，如中心入料管、锥帽、叶轮上、下流道衬板、圆周护板、鄂板的磨损程度，磨损较严重的要及时进行修补或更换，同时更换部件的重量、型号和尺寸等，一定都要按原来的部件参数进行更换。

2、做好润滑工作要经常注意并及时做好摩擦面的润滑工作，且所采用的润滑脂应根据使用的地点、气温条件而定，一般情况下采用钙基、钠基和钙钠基润滑脂;加入润滑脂时应先用洁净的或煤油清洗滚柱轴承的滚道，然后再加入，加入轴承座内的润滑脂应为其空间容积的50%左右，锤破制砂机生产厂家，而且每3~6个月更换一次，这样既确保了机器的正常运转又延长了使用寿命。

3、保持设备的清洁要经常保持设备的清洁，做到无积灰、无油污、不漏油、不漏水、不漏电、不漏灰，更要注意灰尘等杂物不得进入润滑系统和润滑部位，锤破制砂机现货销售，因为这些杂物不仅会破坏润滑油膜，而且会使设备失去润滑而增加磨损，缩短设备的使用寿命;尤其要注意对轴承的定期清洗，破碎机在作2000小时后，打开主轴总成对轴承进行清洗，一般工作7200小时后要更换新轴承。

What are the ********* ********* for ********* *********

1. ********* ********* the wear of ********* ********* of the *********, such as the wear ********* of the ********* ********* tube, cone cap, ********* upper and lower ********* ********* *********, ********* guard *********, and jaw *********. Those with ********* wear ********* be ********* or ********* in a ********* *********. At the same time, the *********, model, and size of the ********* ********* must be ********* ********* to the ********* ********* *********.
2. ********* ********* ********* be paid to and ********* ********* of the ********* ********* when ********* ********* work, and the ********* ********* used ********* be ********* ********* to the ********* of use and ********* *********. *********, ********* based, ********* based, and ********* ********* based ********* ********* are used; When ********* ********* *********, the ********* of the ********* ********* ********* be ********* with clean or ********* first, and then added. The ********* ********* added to the ********* seat ********* be about 50% of its ********* *********. The ********* of the ********* sand ********* ********* ********* ********* it every 3-6 *********, which ********* the ********* ********* of the ********* and ********* its ********* life.
3. To keep the ********* clean, it is ********* to ********* ********* its *********, ********* that there is no ********* of dust, oil, oil, water, *********, or dust. It is also ********* to note that dust and other ********* ********* not enter the ********* ********* and ********* parts. ********* sand ********* ********* are sold in stock ********* these ********* not only ********* the ********* oil film, but also cause the ********* to lose ********* and ********* wear, ********* its ********* life; ********* ********* ********* be paid to ********* ********* of *********. After 2000 hours of *********, the ********* ********* open the main shaft ********* to clean the *********. *********, new ********* ********* be ********* after 7200 hours of *********.